Omega Owners Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please check the Forum Guidelines at the top of the Newbie section

Pages: 1 [2]  All   Go Down

Author Topic: Omega2.5 DTI project  (Read 870 times)

0 Members and 1 Guest are viewing this topic.

VXL V6

  • Omega Lord
  • *******
  • Offline Offline
  • Gender: Male
  • Solihull
  • Posts: 9260
    • 3x 3.2 V6 Elite Saloons
    • View Profile
Re: Omega2.5 DTI project
« Reply #15 on: 07 October 2020, 22:44:04 »

Is the changer missing the flap?
Logged

speedy_ns

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Novi Sad Serbia
  • Posts: 98
    • View Profile
Re: Omega2.5 DTI project
« Reply #16 on: 08 October 2020, 07:33:12 »

Yes. That's how it's been when i bought it. ( wasn't me that broke it I swear  ;D )
I'm chasing donor car anyway, those flaps are interchangeable between units I believe. Also I have CCR 2006 in parts sitting  somewhere..
Next problem are the seats. Passenger seat and rear bench have two small holes in leather. Drivers seat heater doesn't work.
Seats are fully electric, drivers with memory.
Cant' decide should I try to fix them or to replace them. Carpets have to go, but finding another seats with leather in good condition, and all the electrics working will bee tricky..
« Last Edit: 08 October 2020, 07:36:43 by speedy_ns »
Logged

VXL V6

  • Omega Lord
  • *******
  • Offline Offline
  • Gender: Male
  • Solihull
  • Posts: 9260
    • 3x 3.2 V6 Elite Saloons
    • View Profile
Re: Omega2.5 DTI project
« Reply #17 on: 08 October 2020, 08:15:49 »

Yes. That's how it's been when i bought it. ( wasn't me that broke it I swear  ;D )
I'm chasing donor car anyway, those flaps are interchangeable between units I believe. Also I have CCR 2006 in parts sitting  somewhere..

OK, Was going to say that I can send you a front bezel with CDC flap if needed  :y
Logged

speedy_ns

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Novi Sad Serbia
  • Posts: 98
    • View Profile
Re: Omega2.5 DTI project
« Reply #18 on: 08 October 2020, 08:47:08 »

That's nice of you, but shipping to Serbia would cost more than full Bose setup anyway  :D
Those flaps cause problems even when they work.
I remember once I tried to change CD while driving. I managed to brake the gear that drives that flap and almost drive myself off the road.
Logged

speedy_ns

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Novi Sad Serbia
  • Posts: 98
    • View Profile
Re: Omega2.5 DTI project
« Reply #19 on: 15 October 2020, 17:58:51 »

Donor car purchased yesterday.


Someone put 235 55 17 at the rear, 2cm wheel spacers and it didn't rub  ::)
2.5 DTI manual. 400K on the clock and still doing donuts  ;D
I started striping parts to complete mine car, than I'll sell what can bee sold, rest is going to bee scraped.
Both sets of alloys are for sale, cause i don't like them.
Logged

speedy_ns

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Novi Sad Serbia
  • Posts: 98
    • View Profile
Re: Omega2.5 DTI project
« Reply #20 on: 16 October 2020, 18:04:14 »

Quick question:
I'm planning to replace drivers door. Donor car doesn't have Bose, rest is identical.
What are differences in wiring for front door speakers? If there is any..
Logged

VXL V6

  • Omega Lord
  • *******
  • Offline Offline
  • Gender: Male
  • Solihull
  • Posts: 9260
    • 3x 3.2 V6 Elite Saloons
    • View Profile
Re: Omega2.5 DTI project
« Reply #21 on: 16 October 2020, 19:21:28 »

No difference in door wiring, just need to swap the 2Ohm Bose speaker over
Logged

speedy_ns

  • Junior Member
  • **
  • Offline Offline
  • Gender: Male
  • Novi Sad Serbia
  • Posts: 98
    • View Profile
Re: Omega2.5 DTI project
« Reply #22 on: 16 October 2020, 21:59:27 »

Thanks mate  :y
Logged
Pages: 1 [2]  All   Go Up
 

Page created in 0.244 seconds with 22 queries.